Skip to content
(787)-476-7950 Hormigueros, PR 00660

Mon – Fri 7:00 am – 5:00 pm OPEN Saturday-Sunday CLOSED

Dome security camera on a wall-mount bracket inside a modern building

Guide

Security Camera Guide: Pixel Density, Storage, PoE and Hardening

Plan an IP camera system from the task, not from the camera. For each view, decide what a viewer must achieve, from noticing movement to identifying a person, and express it as a pixel density on the target, as IEC 62676-4 does. The density decides the lens and the resolution; with the frame rate and the codec, they give the bitrate, and bitrate times retention days gives the storage. Then budget PoE, put the recorder and switches on a UPS, choose housings by IP and IK rating, keep cameras off the internet and, for U.S. federal work, check Section 889.

Updated November 2026

What each camera must achieve: the IEC 62676-4 levels

IEC 62676-4 links each operational requirement to a pixel density on the target. Its 2014 edition is best known for four of its levels, sometimes called DORI and still quoted as distances on camera datasheets: detection (25 px/m), observation (about 63), recognition (125) and identification (250).

The 2025 edition replaced every 2014 level with seven new ones: Overview (20 px/m), Outline (40), Discern (80), Perceive (125), Characterize (250), Validate (500: known persons verified, a vehicle's plate number retrieved) and Scrutinize (1,500: identity established with high certainty). The levels assume a person watching the video, and pixel density is a simplified model: light direction, optics and compression also change the result.

From pixel density to lens, resolution and low light

Pixel density is the horizontal resolution divided by the width of the scene at the target's distance: 2,560 pixels across a 10 m entrance give 256 px/m; across a 40 m parking lot, 64 px/m.

  • To raise the density, narrow the field of view (a longer focal length, or a varifocal lens zoomed in) or move the camera closer. At the same aspect ratio, four times the megapixels only doubles the horizontal pixels.
  • Give each task its own camera: a wide view for the overview, a tight view of the entrance for identification.

Low light and infrared

At night, many outdoor cameras switch to black and white with built-in infrared. Check the stated infrared range against the real distance, keep eaves and walls out of the beam, and judge night images from footage recorded at the site, not from a minimum-lux figure.

Codecs, storage and where to record

When ITU announced H.265 (HEVC) in January 2013, it said the codec would need only half the bit rate of its predecessor, H.264. Real savings vary by scene, and every recorder and viewing app must decode the codec chosen.

Storage follows from the bitrate: a camera at 4 Mbit/s writes 4 × 86,400 s ÷ 8 = 43,200 MB (43.2 GB) a day, about 1.3 TB in 30 days; sixteen, about 20.7 TB. Measure a sample camera by day and by night, then add disk redundancy (RAID) and free space.

  • Network video recorder (NVR) on site: keeps recording when the internet fails; lock it away, since whoever takes the recorder takes the footage.
  • Cloud: survives theft or damage at the site, but the internet upload must carry every camera that records there.

Keep a copy of the recorder's settings too, as the backup and disaster recovery guide advises for device configurations.

Power over Ethernet for cameras

An IP camera can take its power from the switch over the data cable (Power over Ethernet, PoE). The Ethernet Alliance overview of the IEEE standards gives, per class, the power at the switch port and at the device:

  • Class 3, IEEE 802.3af (Type 1): 15.4 W and 13 W.
  • Class 4, IEEE 802.3at (Type 2): 30 W and 25.5 W.
  • Classes 5 and 6, IEEE 802.3bt Type 3: up to 60 W and 51 W.
  • Classes 7 and 8, IEEE 802.3bt Type 4: up to 90 W and 71.3 W.

Take each camera's maximum draw from its datasheet, with infrared, heater and motors running, and keep the total on each switch below its PoE budget, with room to grow; a camera with a heater or motor may need an 802.3at or 802.3bt port. Heat in cable bundles and the distance limits of copper are covered in the structured cabling guide.

ONVIF profiles: making different brands work together

ONVIF profiles let cameras, recorders and video management software (VMS) from different makers work together, but only for the features of a profile that both products support.

  • Profile S (2011), the original streaming profile: ONVIF support ends on March 31, 2027, after which no new products or firmware will be accepted for Profile S conformance. Registered products stay conformant; the replacement is Profile T.
  • Profile T: H.264 and H.265 streaming, imaging settings, motion and tampering alarms, metadata streaming and two-way audio.
  • Profile G: edge storage and retrieval, such as recording to the camera's own memory card.
  • Profile M: metadata and events for analytics, with events that can be published over MQTT.

For a new system, ask for Profile T on cameras and recorder, and add G or M only where they will be used.

Outdoor housings: IP and IK ratings

IEC 60529 gives an enclosure a two-digit IP code: the first digit, up to 6, for solid objects and dust; the second for water. Second digits 5 and 6 are water-jet tests, 7 and 8 immersion, and 9 high-pressure, high-temperature jets; for wind-driven rain, ask for 5 or 6. The code says nothing about salt or sun: IEC 60529 leaves corrosion, solar radiation and condensation to product standards.

IEC 62262 rates impact resistance from IK00 to IK10; in the table of a white paper by the enclosure maker Rittal, IK08 is 5 joules and IK10 is 20. The paper adds that the IP rating must hold after the impact test: a housing that keeps IP66 only up to IK08 is rated IP66 with IK08. Where people or vehicles can reach a camera, ask for IK10 and the IP rating that held at that level.

Field notes: salt air, sun, storms and power cuts

  • Salt air: near the sea, choose housings and mounts made for corrosive environments, with stainless or coated fasteners, and inspect them regularly.
  • Sun and heat: a housing in full sun runs hotter than the air around it; check that temperature against the camera's operating range and add a sunshield.
  • Humidity: seal cable entries, form drip loops and use sealed junction boxes.
  • Wind: a long focal length magnifies every movement of the mount, so tight identification views need rigid mounts on the building structure, not on swaying poles or thin sheet metal.
  • Surges: have an electrician bond the mounts to the grounding system and fit a grounded surge protector where the outdoor cable enters the building.
  • Power cuts: a PoE camera stops when its switch loses power, so the UPS must carry the switches, the recorder and the router; size it from the PoE total worked out above plus what the switches, recorder and router draw themselves. After each outage, confirm that recording has resumed.

Network separation, hardening and Section 889

CISA's September 2026 advisory on a vulnerable IP camera firmware recommends keeping devices off the internet, behind firewalls and isolated from business networks, and using an up-to-date VPN for remote access. In practice:

  • Put cameras and recorder on their own VLAN, with firewall rules that let users reach the recorder but not the cameras.
  • Forward no router ports to cameras or recorder; view remotely through a VPN or a service that opens no inbound ports.
  • Replace every default password, give each user an individual account, update firmware on a schedule and synchronize clocks (NTP) so that timestamps agree.

Section 889 for U.S. federal contractors

Section 889 of the National Defense Authorization Act for Fiscal Year 2019, applied through FAR clause 52.204-25, bars federal agencies from obtaining equipment or services that use covered telecommunications or video surveillance equipment as a substantial or essential component (since August 13, 2019) and from contracting with entities that use such equipment (since August 13, 2020). The clause names five manufacturers, three of them only for equipment used for public safety, the security of government facilities, physical security surveillance of critical infrastructure and other national security purposes, and covers entities the Secretary of Defense believes are connected to the government of China. Check every camera and recorder brand against the clause text, with contracting or legal advice.

Planning checklist

  1. Each view's level, distance and scene width, not a megapixel count.
  2. Infrared range against the real distance at night.
  3. Retention days and the rules that apply to the site.
  4. Recorder location, disks and UPS runtime.
  5. PoE class of each camera at maximum draw, and each switch's budget.
  6. IP and IK ratings for outdoor cameras and cameras within reach.
  7. ONVIF profiles, network separation, remote access, user accounts and firmware updates.
  8. For federal contractors, a Section 889 check of every brand.

Frequently Asked Questions

What does DORI mean on a camera datasheet?

DORI names four of the levels of the 2014 edition of IEC 62676-4: detection (whether anyone is present), observation (how many people, and details such as distinctive clothing), recognition (whether the viewer has seen the person before) and identification (who the person is). A DORI distance is how far, at a stated lens setting, each level's density is reached, without counting your site's light or compression. The 2025 edition has replaced these levels.

Is a 4K camera always better than a 1080p camera?

Not always. A 4K UHD image is 3,840 pixels wide, twice the 1,920 of 1080p, so at the same density it covers twice the width: at 500 px/m, the Validate level, about 7.7 m against 3.8 m. In exchange it raises bitrate, storage and recorder load. Let the density each view needs set the resolution.

How long should security camera footage be kept?

There is no single figure. Keep footage long enough to notice an incident and retrieve the video: longer for a site checked weekly than for one watched daily. Sector rules, contracts or privacy laws may set minimums or maximums, so check the ones that apply to the site.

Does Section 889 apply to a business without federal contracts?

Not directly: Section 889 binds federal agencies, and FAR clause 52.204-25 passes the prohibition on to their contractors. Its second part, however, reaches equipment a contractor uses outside federal work, so a business planning to bid on federal contracts should check its cameras and recorders before it bids.

About this guide

The author of this guide is GlobalTech Corp., an IT, cybersecurity and network cabling company in Hormigueros, Puerto Rico, with over 25 years of experience. It installs IP security cameras with NVR recording and centralized monitoring, sets up UniFi Protect on UniFi networks and holds the Ubiquiti Network Certification. It serves businesses across Puerto Rico, Vieques and Culebra included. Its security camera service page describes that work, and security cameras in Puerto Rico covers projects on the island. The guide's numbers were last verified in November 2026.

More guides: Technology Guides.